Duratec Thermostat and Housing
Duratec Thermostat and Housing
£40.00
Mechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Specification and Application
| Component | Duratec Thermostat and Housing |
| Type | Mechanical thermostat |
| Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec |
| Applications | Kit Cars Rally/Race – MkI/II Escort, Sierra, Lotus Cortina BriSCA F2 Classic Ford |
Additional information
| Weight | 1 kg |
|---|
Related Products
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Products that you might find interesting
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing Kit
Slave Cylinder for Toyota W Series Hydraulic Release Bearing KitThis slave cylinder is a replacement for the Toyota W Series Hydraulic Release Bearing Kit.
For use with a 0.625 inch (5/8″) master cylinder.
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Duratec Underdrive Pulley 164mm Trigger Wheel
Duratec Underdrive Pulley 164mm Trigger WheelReplaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
Honda K20 or K24 Water Outlet
Honda K20 or K24 Water OutletHonda K20 upper coolant housing that redirects the outlet to 90 degrees from the engine.
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
