Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
$16.80
Converts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Consists of 2 roller bearing races mounted end to end. Allows a Duratec engine to be connected to the Toyota W range of gearboxes using our Duratec Engine to Toyota W Series Gearbox Bellhousing.
Internal spigot diameter is 12mm (0.47″) – Toyota W range of gearboxes
External spigot diameter is 21mm (0.83″)
Length is 6mm (0.24″) x 2
Related Products
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release BearingConnects our Toyota W Series Hydraulic Release Bearing Kit to your car’s pedal box or engine bay mounted master cylinder.
Toyota W Series Hydraulic Release Bearing Kit
Toyota W Series Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox.
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox BellhousingAllows the Ford Duratec engine to be mated to the wide range of Toyota W series 5 speed gearboxes available. These gearboxes, in particular the DW56 are a strong and slick shifting alternative to the Sierra 5 speed boxes, which are increasingly in short supply.
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)For use with the Adaptor Plate for RS2000 Type Bellhousing to 2.8 Gearbox.
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic ClutchThis slave cylinder fits directly to the mounting lug on our Sierra Direct Replacement Hydraulic Clutch Bellhousing and includes an adjustable pushrod.
Cylinder bore is 22mm (7/8”).
