Duratec ARP flywheel bolt set
Duratec ARP flywheel bolt set
£47.70
For all petrol Duratec engines 1.8 litre, 2.0 litre and 2.3 litre. Torque setting 105 ft lbs with 30W oil.
Bolt length under the head is 25mm.
Suitable for the following flywheels:
Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate2.0 or 2.3 Ford Duratec lightweight steel flywheel to suit Twin plate 7 1/4″ paddle clutch. With integral starter ring (ring gear is machined into the flywheel)
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic ClutchThis slave cylinder fits directly to the mounting lug on our Sierra Direct Replacement Hydraulic Clutch Bellhousing and includes an adjustable pushrod.
Cylinder bore is 22mm (7/8”).
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release Bearing
Plumbing Kit for Type 9 or T5 Hydraulic Release BearingConnects our Ford Type 9 Hydraulic Release Bearing Kit or Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch to your car’s pedal box. Comes with fittings and enough pipe to allow the bleed nipple to be situated remotely.
