Honda K20 or K24 ARP flywheel bolt set
Suitable for the following flywheels:
Honda K20 Lightweight Steel Flywheel – Standard Clutch Plate
Honda K20 Lightweight Steel Flywheel – 7 1/4″ 184mm Race Clutch Plate
Additional information
| Weight | 0.2 kg |
|---|
Related Products
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate
Ford Duratec lightweight Steel Flywheel – 7 1/4″ Race Clutch Plate2.0 or 2.3 Ford Duratec lightweight steel flywheel to suit Twin plate 7 1/4″ paddle clutch. With integral starter ring (ring gear is machined into the flywheel)
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
Spigot bearing 10mm internal diameter
Spigot bearing 10mm internal diameterConverts the Zetec SE / Sigma 1.7 VCT crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Rocket input shaft. Fits in standard recess in crankshaft.
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
RS2000 Clutch Cable Adapter Plate
RS2000 Clutch Cable Adapter PlateAdaptor plate with a hole to locate a standard Ford clutch cable. Drilled for the standard RS2000 starter motor hole pattern.
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Toyota W series Hydraulic Release Bearing Kit Without Slave Cylinder
Toyota W series Hydraulic Release Bearing Kit Without Slave Cylinder
Toyota W series Hydraulic Release Bearing Kit Without Slave Cylinder
Toyota W series Hydraulic Release Bearing Kit Without Slave CylinderThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox minus the slave cylinder found in the Toyota W Series Hydraulic Release Bearing Kit.
