Duratec Water Manifold
Duratec Water Manifold
£231.53
Designed to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Specification and Application
| Component | Duratec Water Manifold |
| Type | Cast aluminium pipes and components |
| Engines | Ford 1.8 Duratec Ford 2.0 Duratec Ford 2.3 Duratec Ford 2.5 Duratec |
| Applications | Kit Cars Rally/Race – MkI/II Escort, Sierra, Lotus Cortina BriSCA F2 Classic Ford |
Additional information
| Weight | 4 kg |
|---|
Related Products
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Thermostat and Housing
Duratec Thermostat and HousingMechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Products that you might find interesting
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic Clutch
Slave Cylinder for Duratec Engine to Ford Gearbox Hydraulic ClutchThis slave cylinder fits directly inside our Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing. For use with a 0.625 inch (5/8″) master cylinder.
Duratec Starter Motor
Duratec Starter MotorThis starter motor can be used in conjunction with the Duratec Engine to Ford Gearbox Cable Clutch Bellhousing, Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing, Duratec Engine to Borg Warner T5 or Tremec Gearbox Hydraulic Clutch Bellhousing and Duratec Engine to Toyota W Series Gearbox Bellhousing
Honda K20 or K24 Water Outlet
Honda K20 or K24 Water OutletHonda K20 upper coolant housing that redirects the outlet to 90 degrees from the engine.
Duratec Underdrive Pulley 146mm Trigger Wheel
Duratec Underdrive Pulley 146mm Trigger WheelReplaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing
Anodised Silver Spacer for Billet Aluminium Hydraulic Heavy Duty Release Bearing12mm anodised silver adapter plate which fits between the Billet Aluminium Hydraulic Heavy Duty Release Bearing and its mounting boss.
