Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
$16.76
Converts the 1KR-FE engine crankshaft to accommodate the Toyota W range of gearboxes in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Consists of 1 roller bearing race. Allows a Toyota 1KR-FE engine to be connected to the Toyota W range of gearboxes using our Toyota 1KR-FE Engine to Toyota W Series Gearbox Bellhousing.
Related Products
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and CoverConnects the Toyota 1KR-FE engine to the range of Toyota W Series gearboxes
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox BellhousingAllows the 1.0 litre Toyota 1KR-FE engine to be mated to the range of Toyota W series 5 speed gearboxes available in a longitudinal installation.
Products that you might find interesting
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Borg Warner T5 Hydraulic Release Bearing Kit
Borg Warner T5 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing T5 gearbox. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)
Longer Fine Cap Head Bolts for 2.8 Gearbox (4)For use with the Adaptor Plate for RS2000 Type Bellhousing to 2.8 Gearbox.
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
