Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
Toyota 1KR-FE Engine to Toyota W56 Gearbox Spigot Bearing
£13.00
Converts the 1KR-FE engine crankshaft to accommodate the Toyota W range of gearboxes in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Consists of 1 roller bearing race. Allows a Toyota 1KR-FE engine to be connected to the Toyota W range of gearboxes using our Toyota 1KR-FE Engine to Toyota W Series Gearbox Bellhousing.
Additional information
| Weight | 0.1 kg |
|---|
Related Products
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and Cover
Toyota 1KR-FE Engine to Toyota W Series Gearbox Clutch and CoverConnects the Toyota 1KR-FE engine to the range of Toyota W Series gearboxes
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox Bellhousing
1KR-FE Toyota Engine to Toyota W Series Gearbox BellhousingAllows the 1.0 litre Toyota 1KR-FE engine to be mated to the range of Toyota W series 5 speed gearboxes available in a longitudinal installation.
Products that you might find interesting
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 Gearbox
Slave Cylinder for VW / Audi to Ford Type 9 or Borg Warner T5 GearboxThis slave cylinder fits directly inside our VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing or VW / Audi 1.8 Litre to Ford Type 9 Bellhousing.
For use with a 0.625 inch (5/8″) master cylinder.
Spigot bearing 10mm internal diameter
Spigot bearing 10mm internal diameterConverts the Zetec SE / Sigma 1.7 VCT crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Rocket input shaft. Fits in standard recess in crankshaft.
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot BearingConverts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
