Duratec Underdrive Pulley 146mm Trigger Wheel
Duratec Underdrive Pulley 146mm Trigger Wheel
£184.00
Replaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
- Machined from anodised billet steel
- Complete with integral crank position sensor 36-1 146mm trigger wheel
- 6 groove belt
- Suitable for 2.0 litre and 2.3 litre Duratec engines
- 3mm keyway
- 95mm diameter pulley
- Smaller diameter to prevent over-revving belt driven ancillaries and to save horsepower
NB: improper installation will cause valve train and / or piston damage
* The finish may be gold or matt
Please see our Ford Duratec Engine page for more information.
Additional information
| Weight | 0.5 kg |
|---|
Related Products
Duratec Universal Chassis Mounted Engine Kit
Duratec Universal Chassis Mounted Engine KitThe Duratec Universal Chassis Mounted Engine Kit allows the popular Duratec engine to be fitted in a wide range of RWD vehicles.
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Duratec Thermostat and Housing
Duratec Thermostat and HousingMechanically controlled and replaces standard Mondeo Duratec item that is controlled by the Mondeo ECU.
Duratec Water Manifold
Duratec Water ManifoldDesigned to simplify the cooling system when used in a longitudinal engine position. The depth from the rear cylinder head face is 60mm. Incorporates heater outlet. Comes with temperature gauge sender.
Products that you might find interesting
16 Valve Astra Inlet Manifold
16 Valve Astra Inlet ManifoldTo convert 16 Valve Astra 2.0XE engine to twin Weber 40 or 45 carburettors. Studs & nuts included. Cosworth type mount ‘o’ ring plates not included.
* Please note that the manifold is only compatible with 0 degrees mounted engines, not 7 degree standard angle.
Zetec RWD Starter Motor
Zetec RWD Starter MotorThis starter motor can be used in conjunction with the RS2000 Type Bellhousing (cable clutch), the Sierra Direct Replacement Cable Clutch Bellhousing and Sierra Direct Replacement Hydraulic Clutch Bellhousing bellhousings. Equivalent to LRS707.
NOTE
This starter motor has 10mm less pinion offset to accommodate a standard Zetec E fitted to a Ford Type 9 or Borg Warner T5. Please note that some aftermarket lightweight flywheels are manufactured with a different offset to allow the fitment of standard Pinto or X-flow starter motors. Please check that your flywheel is the standard Zetec E item.
Duratec Universal Chassis Mounted Engine Kit
Duratec Universal Chassis Mounted Engine KitThe Duratec Universal Chassis Mounted Engine Kit allows the popular Duratec engine to be fitted in a wide range of RWD vehicles.
Westfield Duratec Engine Mounting Kit
Westfield Duratec Engine Mounting KitA complete Westfield Engine Mounting Kit
Duratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateDuratec Exhaust Gas Recirculation Valve Blanking Plate
Duratec Exhaust Gas Recirculation Valve Blanking PlateThis aluminium blanking plate replaces the standard exhaust gas recirculation (EGR) valve on all Duratec engines. It improves engine power and assists engine tuning by allowing the engine to use fresh oxygen for the combustion process instead of using recirculated exhaust gas. Simply remove the existing exhaust gas recirculation valve and replace with the blanking plate using silicon gasket sealant. Image shows blanking plate on right and original exhaust gas recirculation valve on left.
Honda K20 or K24 Water Outlet
Honda K20 or K24 Water OutletHonda K20 upper coolant housing that redirects the outlet to 90 degrees from the engine.
Upsell Products
Duratec Underdrive Pulley 164mm Trigger Wheel
Duratec Underdrive Pulley 164mm Trigger WheelReplaces the standard crank pulley on 2.0 and 2.3 litre Duratec engines for higher revving competition engines. Save valuable horsepower by avoiding over-spinning belt driven ancillaries.
