Spigot bearing
Spigot bearing
£15.00
Converts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
Will be required if the following gearbox to engine options do not already have a spigot bearing fitted.
AF14 Duratec Engine to Ford Gearbox
AF15 Duratec Engine to Ford Gearbox Hydraulic Clutch
AF4 Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
AF12 Vauxhall 2.0XE Engine to Borg Warner T5 Bellhousing
AF9 Zetec SE to Type 9 Gearbox Bellhousing *
AF1 RS2000 Bellhousing (when used in conjunction with a Zetec E engine – see FAQ6)
AF58 VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
AF46 VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
Internal spigot diameter is 15mm (0.59″ or 19/32″) – Borg Warner T5* and ford Type 9 gearbox
External spigot diameter is 21mm (0.83″ or 13/16″ or 26/32″)
Length is 16mm (0.63″ or 5/8″)
* Please note that the Ford Puma 1.7 engine has a smaller 17mm spigot bearing hole. You will need to get the input shaft on your gearbox turned down and use our 10mm internal diameter spigot bearing.
Additional information
| Weight | 0.1 kg |
|---|
Related Products
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 Bellhousing
VW / Audi 1.8 Litre to Ford Type 9 BellhousingThis bellhousing will mate the Volkswagen, Audi, SEAT or Skoda 1.8 litre 20 valve turbocharged engines to the Ford Type 9 (Sierra) gearbox.
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 Bellhousing
VW / Audi 1.8 Litre to Borg Warner T5 BellhousingThis bellhousing will mate the Volkswagen, Audi, SEAT or Skoda 1.8 litre 20 valve turbocharged engines to the Borg Warner T5 (2WD Cosworth) gearbox.
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing
Duratec Engine to Ford Gearbox Hydraulic Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a hydraulic clutch.
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch Bellhousing
Duratec Engine to Ford Gearbox Cable Clutch BellhousingThis bellhousing allows the 1.8l, 2.0l or 2.3l Duratec engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a cable clutch.
Zetec SE to Ford Gearbox Bellhousing
Zetec SE to Ford Gearbox BellhousingThis bellhousing will mate the Ford Zetec SE (Sigma)* engine to the Ford Type E (Rocket) 4 speed or Ford Type 9 (Sierra) 5 speed gearbox.
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch Bellhousing
Vauxhall 2.0XE Engine to Ford Gearbox Cable Clutch BellhousingThis bellhousing allows the Vauxhall 2.0XE Engine to be connected to the Ford Type E (Rocket 4 sp) and Type 9 (Sierra 5 sp) gearboxes using a cable clutch.
RS2000 Type Bellhousing (cable clutch)
RS2000 Type Bellhousing (cable clutch)This is an accurate reproduction of the Ford RS2000 (MkI & MkII Escort) alloy bellhousing with optional quick release facility.
Products that you might find interesting
Ford Type 9 Hydraulic Release Bearing Kit
Ford Type 9 Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, replacing the standard gearbox nose. The kit comes completed with replacement seal and fixings. The slave cylinder inlet and bleed should be located vertically and the hydraulic clutch pipe routed through 2 holes drilled in the best location within the bellhousing flange for your application.
10mm Cap Head Bolts (4)
10mm Cap Head Bolts (4)4 10mm x 1 1/2mm pitch cap head bolts for when a quick release bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox externally straight through the original tapped 12mm holes of the Ford gearbox and screwed into the 10mm tapped holes of the quick release bellhousing.
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic Clutch
Adapter Plate for Duratec Engine to Ford Gearbox Hydraulic ClutchAdapter plate which fits between the Duratec Engine to Ford Gearbox Hydraulic Clutch Bellhousing and a Type E (Rocket) or Type 9 (Sierra) gearbox.
You will also need our Slave Cylinder for this conversion
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic Clutch
Slave Cylinder for Sierra Direct Replacement Hydraulic ClutchThis slave cylinder fits directly to the mounting lug on our Sierra Direct Replacement Hydraulic Clutch Bellhousing and includes an adjustable pushrod.
Cylinder bore is 22mm (7/8”).
2000e Clutch Release Bearing
2000e Clutch Release Bearing2000e clutch release bearing. Smaller internal diameter to suit the 7/8″ input shaft sleeve.
