Duratec Engine to Toyota W56 Gearbox Spigot Bearing
Duratec Engine to Toyota W56 Gearbox Spigot Bearing
£13.00
Converts crankshaft to accommodate the Toyota W56 5 Speed Gearbox in a RWD installation. Needed in order to support the longer length of the Toyota gearbox input shaft. Fits in standard recess in crankshaft.
Consists of 2 roller bearing races mounted end to end. Allows a Duratec engine to be connected to the Toyota W range of gearboxes using our Duratec Engine to Toyota W Series Gearbox Bellhousing.
Internal spigot diameter is 12mm (0.47″) – Toyota W range of gearboxes
External spigot diameter is 21mm (0.83″)
Length is 6mm (0.24″) x 2
Additional information
| Weight | 0.1 kg |
|---|
Related Products
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release Bearing
Plumbing Kit for Toyota Hydraulic Release BearingConnects our Toyota W Series Hydraulic Release Bearing Kit to your car’s pedal box or engine bay mounted master cylinder.
Toyota W Series Hydraulic Release Bearing Kit
Toyota W Series Hydraulic Release Bearing KitThis kit utilises a concentric release bearing and aluminium boss, with modification to the standard gearbox nose. The kit comes completed with all fixings required to convert your existing Toyota W series gearbox.
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox Bellhousing
Duratec Engine to Toyota W Series Gearbox BellhousingAllows the Ford Duratec engine to be mated to the wide range of Toyota W series 5 speed gearboxes available. These gearboxes, in particular the DW56 are a strong and slick shifting alternative to the Sierra 5 speed boxes, which are increasingly in short supply.
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate
Ford Duratec lightweight Steel Flywheel – 8 1/2″ Clutch Plate2.0 or 2.3* Ford Duratec lightweight steel flywheel to suit Ford 8 1/2″ clutch plate. With integral starter ring (ring gear is machined into the flywheel).
Products that you might find interesting
Spigot bearing
Spigot bearingConverts crankshaft to accommodate a RWD gearbox. Needed in order to support the longer length of the Type 9 or Borg Warner T5* input shaft. Fits in standard recess in crankshaft.
* With 15mm spigot
RS2000 Clutch Release Bearing
RS2000 Clutch Release BearingGenuine Ford RS2000 clutch release bearing. Will fit most Ford Pinto, Vauxhall XE or Zetec installations. 34mm (1.36″) internal diameter *
* Please note that some USA derived Borg Warner T5 gearboxes have an outside diameter of the release bearing tube of 1.43″. In this instance you will need to mill the release bearing tube down to slightly less than the 34mm (1.36″) internal diameter of the RS2000 clutch release bearing
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford Gearbox
Adapter Plate for Ford Bellhousing to 2.8 Ford GearboxAdapter plate which fits between any of our Ford gearbox bellhousings and a Type 9 (Sierra) 2.8 gearbox. The 2.8 gearbox uses a longer 1st motion shaft hence the need for an adaptor plate.
RS2000 Clutch Release Fork
RS2000 Clutch Release ForkHigh quality UK manufactured RS2000 clutch release fork.
Fine Cap Head Bolts (4)
Fine Cap Head Bolts (4)4 12mm x 1 1/2mm pitch x 40mm long fine cap head bolts for when a standard fitment bellhousing is specified. These bolts allow the bellhousing to be attached to the Ford gearbox internally.
